Pego Electronics (Yi Chun) Company Limited
Pego Electronics-Focus on developing and promoting IEC lab testing equipments
Add to Cart
Go Not Go Gauges for Lampholder E14 Plug Gauge and Contact Gauge 7006-25 7006-26
Go gauges for screw threads of E14 lampholders (figure number: 7006-25-7)
Purpose: to check the minimum dimensions of the lampholder screw thread and dimension X shown on sheet 7005-20
Testing: it shall be possible to screw the gauge into the lampholder without using undue force.
Not go gauges for screw threads of E14 lamp holders (figure number: 7006-26-4)
Purpose: to check the maximum minor diameter of the screw thread, dimension D2 of lampholder E14.
Testing: the screw thread of the lampholder shall be assumed to be correct if the gauge does not enter by its own weight so far that the thread protrudes beyond surface T.
Plug gauge for E14 lampholder for testing contact making ( 7006-30-2)
Note: the application of this gauge is restricted to lampholders for lighting fittings equipped with the lamps (candle lamps, round bulb lamps, domestic tubular lamps, pygmy lamps) when these are fitted with E14 caps, in accordance with sheet 7004-23
Plug gauge for lampholder E14 with candle sharped shaft for candle lamps for testing contact making (7006-30A-1)
This gauge is to be used for testing contact making in lampholders with candle sharped shafts designed especially to make candle lamps only.
Gauge for testing contact-making and protection against accidental contact during insertion of lamps E14 lampholder (figure number: 7006-31-4)
Note: the application of this gauge is restricted to lampholders for lighting fitting equipped with lamps (candle lamps, round bulb lamps, tubular lamps, pygmy lamps) when these are fitted with E14 caps, in accordance with sheet 7004-23
Picture:
List of Gauge for Lampholder:
| Figure number | Description |
| E14 Lampholder Gauge | |
| 7006-25-7 | Go Gauge |
| 7006-26-4 | Not Go Gauge |
| 7006-30-2 | Plug gauge for E14 lampholder for testing contact making |
| 7006-30A-1 | Plug gauge for lampholder E14 with candle shaped sharp for candle lamps for testing contact making |
| 7006-31-4 | Gauge for testing Contact making and protection against accidental contact during insertion of lamps in lampholder |
| BS EN60238 Figure 5 | Test caps for lampholders E14 |
| BS EN60238 Figure 11 | Test Caps for Lampholders E14 |
| BS EN60238 Figure 13 | test cap A and Test cap B for Lampholders E14 |
| E40 Lampholder Gauge | |
| 7006-25-7 | Go Gauge for screw threads of lampholder |
| 7006-26-4 | Not Go Gauge for screw threads of lamphoder |
| 7006-23-3 | Gauge for protecting against Bulb-neck damage and for testing contact-making in lampholder |
| 7006-24-3 | Plug gauge for lampholders for testing protection against accidental contact |
| BS EN60238 Figure 5 | Test Cap for Lampholders E40 |
| BS EN60238 Figure 11 | Test Cap for lampholders E40 |
| BS EN60238 Figure 15 | Test Cap for lampholders E40 |
| E27 Lampholder gauges | |
| 7006-25A-2 | "Go" Gauge for Lampholders E27 |
| 7006-26-4 | “Not Go” Gauges for Screw threads of lampholders E27 |
| 7006-21-5 | Gauge for testing protection against bulb-neck damage and for testing contact-making in lampholders E27 |
| 7006-22A-4 | Gauge for Testing contact-making and protection against accidental contact during insertion of lamps in lampholders E27 |
| 7006-22B-1 | Gauge for detecting side-contacts with ctting-edges in lampholders E27 |
| 7006-22C-1 | Gauge I for checking side contact resiliency in lampholders E27 |
| 7006-22D-1 | Gauge II for checking side contact resiliency in lampholders E27 |
| IEC60238 figure 11 | test cap for tests of insulation resistance, electric strength and temperature rising |
| IEC60238 figure 5 | test caps |
| IEC60238 figure 14 | test caps for lampholder E27 |
Note: We accept customized gauges, please just send us the figure number on the inquiry, all the gagues can pass the third-lab calibration and get the ceritificates autorized by CNAS (IS017025).