Pego Electronics (Yi Chun) Company Limited
Pego Electronics-Focus on developing and promoting IEC lab testing equipments
Add to Cart
The IPX1 and IPX2 Ingress Protection Testing Machine is designed and manufactured according to IEC60529, IEC60598-1, GB4208, and GB7000.1 standards. It is suitable for the drip level waterproof test of outdoor electrical and electronic products, lighting products, and medical product shells. It is suitable for certification and testing agencies and manufacturers to conduct IPX1 and IPX2 waterproof inspections of products. This equipment uses PLC control, and a 7-inch color touch screen displays, controls, and sets the test program. Users can easily and simply reach the test conditions. The equipment is equipped with a precision glass rotor flowmeter, which controls the actual output flow through manual adjustment.
IEC60529 Degrees of protection provided by enclosures (IP Code) Figure 3
IEC60598-1 Luminaires - Part 1: General requirements and tests
ISO20653 Road Vehicles - Degrees of protection (IP-Code) - Protection of electrical equipment against foreign objects, water and access
| Model | IPX12B-800 | IPX12B-1000 |
| Drip board size (mm) | 800*800 | 1000*1000 |
| Outer size (mm) | 1000*1000*2300 (L*W*H) | 1500*1200*2360 (L*W*H) |
| Diameter of turntable | Φ500mm | Φ600mm |
| Aperture of nozzle | Φ0.4mm | |
| Grid pattern | 20*20mm | |
| Delivery rate | 1~3mm/min (±0.5mm/min) | |
| Adjust mode | Manual adjustment | |
| Lifting height of drip board | 800~1800mm (adjustable) | |
| Max. load-bearing capacity of turntable | 50KG | |
| Rotation speed of turntable | 1r/min (IPX1) | |
| Tilt angle of turntable | 00 or 150 in 4 positions | |
| Lifting height of turntable | fixed | |
| Test time | 0~999min | |
| Protection device | Electric leakage, hydropenia, short circuit | |
| Working power | AC 220V/50Hz, 1KW (Live wire + neutral wire + protective ground wire) | |
| Working conditions | 5℃~35℃ (temperature), ≤85% (R.H.), 86kPa~106kPa (pressure) | |
| Accessories | Water filter*1, test needle*100, brass needle holder*20, 3-core cable*1 (3m) | |
| Water source | 1). The user is required to configure a water source for the equipment at the installation site, with a water pressure not less than 0.2Mpa, and install a 4/8 inch faucet. 2). The faucet is not more than 2 meters away from the equipment | |
| Requirement for the site | The ground is level, the drainage is unobstructed, the ground and walls are waterproofed, and the floor drain or drainage ditch is set | |
| Requirement for power switch | 1). The user is required to configure the leakage protection air switch of the corresponding capacity for the equipment at the installation site, and this switch must be independent for the use of the equipment 2). It is forbidden to use knife switches or power sockets 3). The leakage protection air switch is not more than 2 meters away from the equipment | |
4.1 What parts does the ipx1 and ipx2 ingress protection testing machine consists of?
Pego: The ipx1 and ipx2 ingress protection testing machine consists of the control system, frame, drip board, needles, turntable, flowmeter and etc.
4.2 Will any replacement be deliveried together with the machine?
Pego: Yes, we have prepared extra 100pcs needle and one water filter for the machine.
4.3 Does the ipx1 and ipx2 ingress protection testing device have the air drying function?
Pego: Yes, the machine has the compressed air drying function. After the test is completed, the excess water in the drip box can be drained clean to avoid long-term accumulation of water and scaling to block the pinholes. But user need to provide the compressor themselves.
